HP0-J26試験問題 最新のテストと回答を提供し 無料ダウンロートできます [資格]
IT分野でHP Certification I 認証は必要とされている認証テストの一つ、HP0-J26試験もHP Certification I 認証の最も重要の試験テストになっています、でも、安心してください！killtestはHP0-J26テストの最新問題集を提供し、一発合格することも保証いたします！killtestの試験問題集は世界中で最も権威的な専門家が研究して作りあがた作品でございます！
HP0-J26
Designing and Implementing HP SAN Solutions
1.To install additional switches, you must determine the ideal ISL ratio. Which ISL ratio range is
recommended for less I/O intensive application requirements (less than 70 MB/s at 2 Gb/s, less
than 140 MB/s at 4 Gb/s, less than 280 MB/s at 8 Gb/s)?
A.3:1 to 1:1
B.1:1 to 3:1
C.15:1 to 7:1
D.7:1 to 15:1
Answer:B
2.Which Fibre Channel timing variables must match in an interoperable fabric?
A.Timing variables do not need to match.
B.R_A_TOV, E_D_TOV and B_B_TOV
C.R_A_TOV and E_D_TOV
D.R_A_TOV and B_B_TOV
Answer:C
3.You are preparing an installation plan for implementing a new SAN design and want to ensure all
customer needs are included. Which data collection method requires that you create a process
list and review all relevant stakeholders?
A.Card Arrangement
B.Information Extraction
C.Brainstorming
D.Process Mapping
Answer:B
4.Which information should be included in the topology map documentation of a SAN design
provided to your support organization? (Select two.)
A.serial numbers of connected servers
B.SAN switch zoning configurations
C.storage controller operating mode parameters
D.IP addresses of the connected servers
E.World Wide Names of all nodes and devices
Answer:B C
5.You are implementing a SAN infrastructure including an HP StorageWorks EVA4400 at a
customer site. The customer is interested in using three-site cascaded replication functionality.
What should you recommend to accomplish this? (Select two).
A.HP StorageWorks FlexCopy
B.HP Continuous Access EVA
C.additional disks in the EVA
D.HP Virtual Replicator
E.HP Business Copy EVA
Answer:B E
6.Which HP tool provides the ability to create a Microsoft Visio diagram of a SAN topology for a
customer documentation?
A.SAN Health
B.SAN Designer
C.SAN Visibility
D.SAN Navigator
Answer:C
7.A single Fibre Channel router is implemented in an existing SAN. What can be accomplished?
A.fabric management service
B.fabric interconnection without merge
C.SAN availability improvement
D.SAN extension across long distances
Answer:B
8.Which features can affect performance in a SAN? (Select three.)
A.cable modes
B.number of ISLs
C.type of LC connector
D.storage array configuration
E.type and capacity of disks used
F.storage access restrictions
Answer:B D E
9.What has the most influence on the response time of a hard disk drive?
A.arbitration
B.host request
C.rotational delay
D.seek time
Answer:C
10.You are preparing for a homogeneous fabric merge and notice the customer set the same
domain ID for all fabrics. What will happen if this is not corrected?
A.Enabled zone configurations are immediately disabled.
B.Domain IDs remain unchanged and the fabrics become segmented.
C.Domain IDs are automatically renumbered and the fabrics merge, but port zoning is affected.
D.Domain IDs are automatically renumbered and the fabrics merge without any side effect.
Answer:B
HP0-J26
Designing and Implementing HP SAN Solutions
1.To install additional switches, you must determine the ideal ISL ratio. Which ISL ratio range is
recommended for less I/O intensive application requirements (less than 70 MB/s at 2 Gb/s, less
than 140 MB/s at 4 Gb/s, less than 280 MB/s at 8 Gb/s)?
A.3:1 to 1:1
B.1:1 to 3:1
C.15:1 to 7:1
D.7:1 to 15:1
Answer:B
2.Which Fibre Channel timing variables must match in an interoperable fabric?
A.Timing variables do not need to match.
B.R_A_TOV, E_D_TOV and B_B_TOV
C.R_A_TOV and E_D_TOV
D.R_A_TOV and B_B_TOV
Answer:C
3.You are preparing an installation plan for implementing a new SAN design and want to ensure all
customer needs are included. Which data collection method requires that you create a process
list and review all relevant stakeholders?
A.Card Arrangement
B.Information Extraction
C.Brainstorming
D.Process Mapping
Answer:B
4.Which information should be included in the topology map documentation of a SAN design
provided to your support organization? (Select two.)
A.serial numbers of connected servers
B.SAN switch zoning configurations
C.storage controller operating mode parameters
D.IP addresses of the connected servers
E.World Wide Names of all nodes and devices
Answer:B C
5.You are implementing a SAN infrastructure including an HP StorageWorks EVA4400 at a
customer site. The customer is interested in using three-site cascaded replication functionality.
What should you recommend to accomplish this? (Select two).
A.HP StorageWorks FlexCopy
B.HP Continuous Access EVA
C.additional disks in the EVA
D.HP Virtual Replicator
E.HP Business Copy EVA
Answer:B E
6.Which HP tool provides the ability to create a Microsoft Visio diagram of a SAN topology for a
customer documentation?
A.SAN Health
B.SAN Designer
C.SAN Visibility
D.SAN Navigator
Answer:C
7.A single Fibre Channel router is implemented in an existing SAN. What can be accomplished?
A.fabric management service
B.fabric interconnection without merge
C.SAN availability improvement
D.SAN extension across long distances
Answer:B
8.Which features can affect performance in a SAN? (Select three.)
A.cable modes
B.number of ISLs
C.type of LC connector
D.storage array configuration
E.type and capacity of disks used
F.storage access restrictions
Answer:B D E
9.What has the most influence on the response time of a hard disk drive?
A.arbitration
B.host request
C.rotational delay
D.seek time
Answer:C
10.You are preparing for a homogeneous fabric merge and notice the customer set the same
domain ID for all fabrics. What will happen if this is not corrected?
A.Enabled zone configurations are immediately disabled.
B.Domain IDs remain unchanged and the fabrics become segmented.
C.Domain IDs are automatically renumbered and the fabrics merge, but port zoning is affected.
D.Domain IDs are automatically renumbered and the fabrics merge without any side effect.
Answer:B
コメント 0